Automatic Slide Door Systems. Automatic Bifold Door Systems. Swing Door Operators. Dura-Care ICU-CCU Manual Doors. ProCare 8300 ICU-CCU Manual Doors. ECO Pro Quick Start and Advanced Guide. If your Stanley garage door opener remote control will not work, or has a short range, it may be a matter of changing out an old battery with a new one. If that doesn't fix the problem, move or coil the antenna wire on the opener. If neither of these works, review the 'Remote Control Programming' section of your owner's manual. Stanley Professional 7100 Manual. Heavycareer.netlify.com › Stanley Professional 7100 Manual. Stanley garage door opener compatibility chart For model numbers listed Pre 1982 with serial numbers 08214 or lower parts are no longer available. For model number listed Pre 1982 with serial numbers 08215 or higher you can use our remote #5012. I have a Stanley garage door opener model 7100. I know Stanley doesn't make openers anymore and I can't find the manual online. I had to disengage the opener do to a power out and now I can't re-engage the opener. Thanks so much:-).
| Title | View/Download | Manual Type |
|---|---|---|
| Stanley MC521 Pro Controller | Login or Create an Account to gain access | Service Manuals, Slide Doors |
| Title | View/Download | Manual Type |
|---|---|---|
| C2150 Linear Drive C2150 Control with Version 1 Software and Encoders for Series 2000 Electric Slide Door Operators SETUP INSTRUCTIONS & TROUBLESHOOTING. To be used with G200 Installation Instructions | Login or Create an Account to gain access | Slide Doors |
| Series 2003 Belt Drive Series 2003 Belt Drive Electric Slide Door Operator Installation Instructions | Login or Create an Account to gain access | Slide Doors |
| 2001, 2003 & Profiler B Series with C2150 Control C2150 Control with Version 1 Software and Encoders for Series 2000 Electric Slide Door Operators SETUP INSTRUCTIONS & TROUBLESHOOTING. To be used with G200 Installation InstructionsC2150 Control with Version 2 Software and Encoders for 2001, 2003 & Profiler-B Electric Slide Door Operators SETUP INSTRUCTIONS & TROUBLESHOOTING To be used with either G2001, G230, G230T, G205 or G20B Installation Instructions | Login or Create an Account to gain access | Slide Doors |
| Series 2000 Linear Series 2000 Linear Drive Slide Door INSTALLATION INSTRUCTIONS To be used with H210 C2150 Ver.10 Control Setup Instructions | Login or Create an Account to gain access | Slide Doors |
| Profiler B Slide Door Profiler -B Series Belt Drive Electric Slide Door Operator INSTALLATION INSTRUCTIONS To be used with H202 C2150 Ver.2 Control Setup Instructions | Login or Create an Account to gain access | Slide Doors |
| C2150 Control: ver 10 C2150 Control with Version 10 Software for Series 2000, 2000B, 2001 & 2003 Electric Slide Door Operators SETUP INSTRUCTIONS & TROUBLESHOOTINGTo be used with either G200, G2001, G230, G230T, G205 or G20B Installation Instructions | Login or Create an Account to gain access | Slide Doors |
| C2150 Control: ver 1 C2150 with Version 1 Software and Micro-Switches for Series 2000 Electric Slide Door Operators SETUP INSTRUCTIONS & TROUBLESHOOTING. To be used with G200 Installation Instructions. | Login or Create an Account to gain access | Slide Doors |
| Title | View/Download | Manual Type |
|---|---|---|
| Dorma ESA II Control Manual | Login or Create an Account to gain access | Service Manuals |
| Title | View/Download | Manual Type |
|---|---|---|
| Nabco/GryoTech Gemini 710 | Login or Create an Account to gain access | Service Manuals |
Stanley Garage Door Opener 3200
| Problems | Solutions |
| Opener does not work | A. Make sure power cord is plugged into a properly grounded 3 prong 120 volt outlet. Plug in a drill or other electrical tool to test for power. B. If opener has been cycled several times, the motor overload protector may be activated. Wait approximately 10 minutes for the motor to cool and then try again. C. If a four-function wall console is being used, make sure the vacation switch is in the “UNLOCKED' position. D. If door is severely out of balance. the opener may not be able to exert enough force to move it. Make sure all locks arc removed. Pull the emergency disconnect cord to release the door from the opener. Check to see if the opener will operate if not connected to the door. |
| Hand held transmitter does not work or has shortrange | A. Someone else’s radio controls may be interfering with yours. Try changing your code. B. The battery in your transmitter may be dead or weak. Replace it with a 9 volt battery of the same type. C. Try moving or coiling the antenna wiie on the opener. D. CB radios, computer equipment, powerful communication signals. and other door openers may cause undesirable interference and shorten radio range. |
| Pushbutton does not work | A. Make sure the pushbutton wires are not touching each other at the rear of the opener or at the pushbutton. B. If the wires arc not touching cach other and the problem still exists, disconnect the wires from the back of the opener and “shoit” across the two pushbutton screws using a key or screwdriver. If opener now operates, die pushbutton wires arc probably shorted or broken. |
| Lights flashing on opener | A. This may be caused by activating the obstruction system that is controlled by the open or close force adjustment on the rear of the opener. If it requires more force to move the door than the opener can supply this system will activate. A common cause is a poorly operating door or an obstruction. B. If the beam sensor is not aligned and working correctly, the door can only be closed by holding the wall-mounted pushbutton. The transmitter cannot be used to close the door. The light on the opener will flash and the door will reverse and open if button is not held until the door is fully closed. C. If something obstructs the door while closing, it will reverse and open lights will flash. If something obstructs the door while opening, it will stop lights will flash. |
| Door closes then opens when reaching the floor | A. Is there a rake handle, garden hose, snow, it, etc. obstructing the door? Remove the obstruction then try closing the door again. B. Due to climatic conditions many concrete floors will heave or sink. Turn the (small black) close travel adjustment 1/4 turn opposite the direction of the arrow on the cover |
| Opener activates by itself | A. Somebody may be using the same radio code as you. DO NOT leave radio code switches in factory set position. Review “Radio Coding Instructions.' |
| Excessive tube bow | A. Check to sec that the power head is securely mounted and the door operates freely. Review “Door Balance Tests'. Is something obstructing the door? |
| Light stays on | A. The light time delay on the opener will keep the light on for approximately 4 1/2 minutes after the system has been activated, then will turn it off automatically. B. If opener has a work light switch (which is supplied only with a four-function wall console), slide switch to 'OFF' position. C. If opener has a pedestrian light switch, (which is supplied only with a four-function wall console), the light will stay on for 4-1/2 minutes after the pedestrian door is opened. |
| Not enough open or close travel adjustment | A. If you operated the power unit before it was completely installed or if you did not position the traveler the correct distance from the tube support, the limits and traveler may be out of synchronization. B. Turn off power, remove and relocate traveler by disconnecting chain from sprocket, reassemble and try adjusting again. |
| Something broke need assistance? | A. Reference the proper for all adjustments and settings. B. If the problem has been located in the radio controls (other than batteries) return only the transmitters and the control board. DO NOT return the complete opener. |